under construction

[Team T&E]

replaced 4 6500xxx amps with the new OKUR 7500.1 (2) and let me say wow I set the amps the same as the 6500's. gain set 1/4, set 0 bass boost went on the same volume same freq. first burb and spit out 3 subs after some fine tunning conclusion 1 OKUR 7500.1 is as strong as all 4 6500's, wow I would not have emagined that and I had a far less voltage drop. the protection on the amps were awsome as soon as the subs went it protected it's self removed the bad subs and good to go. pics will be up soon as I can load them up. the car has been through a make over with the help of danny hays we are both extreamly proud and ready for the new sesson hope to see all of you guys soon.

[PHATBOi]

WOW!

http://i685.photobucket.com/albums/vv213/phatboi1282/350342463_o.jpg

A7 7500.1
Features:
Introducing the "Okur" series from db Drive. Technology enhancements, power and control. Performance has never been better. Join the Road to One Eighty and fit your ride with one of db Drive's Okur Amplifiers. We developed all amplifiers on the same technology platform so your only decision is to decide which amplifier suits your ride.



7500WATTS AT 16v!!!

Specifications:
RATED POWER 14.4 VOLTS: 1 X 6500 WATTS @ 1 OHMS
RATED POWER 14.4 VOLTS: 1 X 4000 WATTS @ 2 OHMS
RATED POWER 14.4 VOLTS: 1 X 2000 WATTS @ 4 OHMS
Frequency Response: 20Hz ~ 250Hz
Signal to Noise Ratio: 100dB
Damping Factor: 250<
Efficiency @ 4ohm: 85%
Low Level Input: 6V - 0.2mV
Low Pass Filter (@ 24dB Slope): Variable 35-250Hz
Bass Boost @ 45Hz: Variable 0-9dB
Subsonic Filter (@ 24dB Slope): Variable 10-50Hz
Phase Shift: Variable 0-180 degree
Master/Slave (Linkable): Yes
Remote Level Control: Yes
RCA Line Output: Yes
Working Voltage: 8.5 - 18 Volts

[Team T&E]

WOW!

A7 7500.1
Features:
Introducing the "Okur" series from db Drive. Technology enhancements, power and control. Performance has never been better. Join the Road to One Eighty and fit your ride with one of db Drive's Okur Amplifiers. We developed all amplifiers on the same technology platform so your only decision is to decide which amplifier suits your ride.



7500WATTS AT 16v!!!

Specifications:
RATED POWER 14.4 VOLTS: 1 X 6500 WATTS @ 1 OHMS
RATED POWER 14.4 VOLTS: 1 X 4000 WATTS @ 2 OHMS
RATED POWER 14.4 VOLTS: 1 X 2000 WATTS @ 4 OHMS
Frequency Response: 20Hz ~ 250Hz
Signal to Noise Ratio: 100dB
Damping Factor: 250<
Efficiency @ 4ohm: 85%
Low Level Input: 6V - 0.2mV
Low Pass Filter (@ 24dB Slope): Variable 35-250Hz
Bass Boost @ 45Hz: Variable 0-9dB
Subsonic Filter (@ 24dB Slope): Variable 10-50Hz
Phase Shift: Variable 0-180 degree
Master/Slave (Linkable): Yes
Remote Level Control: Yes
RCA Line Output: Yes
Working Voltage: 8.5 - 18 Volts

6500 watts @ 14.4 volts @ 1ohm
17.9 Volts @ .7 st***** = ?

[Team T&E]

did I mention you could strap them at .35 ohms
no thats not in the hand book :)

[PHATBOi]

Holy ****!

[Big dave]

thoes seam pretty nasty

[Team T&E]

I didn't belive it my self when danny was telling me how strong thease amps were but now I'm a beliver. not really that affordable but with that kind of power what is. sug retail is like $4200.00 each.

[CandeShop]

ha stetsom dont charge that much and have 7k, 11k, 14k

[Team T&E]

ha stetsom dont charge that much and have 7k, 11k, 14k

true but DB Drive seems to think that the amp is worth every penny, right now I would have to agree.

danny use's 3 7500.1 and does what I think 180.1 was the best so far stetsom use's how many amps to do the same db ? I don't know thats why I'm asking please fill me in.

[WaTTz305]

i would love to see stetsom going down to .34 ohms lawl

[CandeShop]

to burp i'm sure a stetsom on proper electrical can be wired to .34 ohms nominal...keyword is nominal i highly doubt that with impedence rise that the db drive amp is seeing under 1 ohm. but i could be wrong..

[CandeShop]

true but DB Drive seems to think that the amp is worth every penny, right now I would have to agree.

danny use's 3 7500.1 and does what I think 180.1 was the best so far stetsom use's how many amps to do the same db ? I don't know thats why I'm asking please fill me in.


4 7kd's and 1 9918z...1 sub to do the 181.7 he is known for.

[Team T&E]

to burp i'm sure a stetsom on proper electrical can be wired to .34 ohms nominal...keyword is nominal i highly doubt that with impedence rise that the db drive amp is seeing under 1 ohm. but i could be wrong..

yup could be.

[Team T&E]

4 7kd's and 1 9918z...1 sub to do the 181.7 he is known for.

at what show was that that is an awsome score. I never herd it that high.

[CandeShop]

at what show was that that is an awsome score. I never herd it that high.

correction 180.5 was with 1 99z and 4 amps (back in 07).. his 181.7db was 4 DD9915z and 4 amps stetsom 10kds (2009)

[Team T&E]

so conclusion is the OKUR 7500.1 worth the money I think so.

[CandeShop]

so conclusion is the OKUR 7500.1 worth the money I think so.

idk i'm not sold on it...its 4000 on ebay and puts out the same as a stetsom 7kd (made back in 2007) on 16v... ratings of the 7kd are as follows

12V @ 1 ohm- 6000w
14V @ 1 ohm- 7225w
16V @ 1 ohm- 9430w
18V @ 1 ohm- 11,000w

compared to the $4k db drive

7500WATTS AT 16v!!!
14.4 VOLTS: 1 X 6500 WATTS @ 1 OHMS

i mean you run what you want..i'm just showing 1 option out there for 1/4 the price

[Team T&E]

idk i'm not sold on it...its 4000 on ebay and puts out the same as a stetsom 7kd (made back in 2007) on 16v... ratings of the 7kd are as follows

12V @ 1 ohm- 6000w
14V @ 1 ohm- 7225w
16V @ 1 ohm- 9430w
18V @ 1 ohm- 11,000w

compared to the $4k db drive

7500WATTS AT 16v!!!
14.4 VOLTS: 1 X 6500 WATTS @ 1 OHMS

i mean you run what you want..i'm just showing 1 option out there for 1/4 the price

not all watts are created equal & does it have the same protections I think not.

[JBLCAMRY]

its just a zenon board in a db drive case. not worth 4k at all imho.

same as a DD Z2LV and a few others.

[Team T&E]

its just a zenon board in a db drive case. not worth 4k at all imho.

same as a DD Z2LV and a few others.

please show us the link were it shows both boards or are you just speculating.
what does the ddz2lv sale for?

[TeamXDMatt]

would like to see you clamp them and see how much power your actually getting out of them with imp rise... just curious

[JBLCAMRY]

db drive,

http://caraudio.com/forum/attachments/amplifiers/26515028d1259813336-guess-what-amp-dsc02387-jpg

ddz2vl
http://i213.photobucket.com/albums/cc256/usask8er1/Amps/080820081787.jpg

[JBLCAMRY]

and the dd is an older amp, 95% sure they don't sell new anymore. but they go for 1500ish used.

[Team T&E]

db drive,

http://caraudio.com/forum/attachments/amplifiers/26515028d1259813336-guess-what-amp-dsc02387-jpg

ddz2vl
http://i213.photobucket.com/albums/cc256/usask8er1/Amps/080820081787.jpg

nice pics but you still have not showed me us a pic of the 7500.1 and no the first pic is not it.

makes you say man danny is the best than if he use's such low end not so powerfull amps (3) of them and does 180db emagin if he used 3 stetsom 14k. no not really. there are so the cactus,atomic,AA thay are all the same is what your implieing.

[Team T&E]

would like to see you clamp them and see how much power your actually getting out of them with imp rise... just curious

sure as soon as I get the new subs back, trying to help with the changes to the WDX's.

[Baracka Flocka Flame]

i would love to see stetsom going down to .34 ohms lawl

someone ask me about my stetsom adventure:rolleyes2:

[Team T&E]

someone ask me about my stetsom adventure:rolleyes2:

sure give me your input on your adventures with stetsom.

[JBLCAMRY]

that is a pic of the 7500.1.

[JBLCAMRY]

and i never said they were low end amps. Zenon makes some of the highest quality amps out there. but the price tag of 4k is a little unreasonable considering others built by the same factory using the same board are less expensive.

[Team T&E]

and i never said they were low end amps. Zenon makes some of the highest quality amps out there. but the price tag of 4k is a little unreasonable considering others built by the same factory using the same board are less expensive.

mine are different, but you said around 1600 used right well how about new we are talking sug retail and it could be the same basic board with different components with different tolerances thus output would be different. lets see again so cactus,atomin,AA, and many others that use the same board are really the exact thing out put wise. I'm sure this is a question many here would really like a posative anwser. tsns,cliff,lanzar all use the same basket motor struckture looks the same as do the spiders but the out put are totally differant right when you get to the nity gity they really are differant.

[JBLCAMRY]

of course there are subtle differences in actual components that are used on board for each said company. i don't know what the dd's went for new, as i said, i don't think they are being produced anymore through dd. and as far as comparing subs to amps...

those subs may use the same baskets, but it is obvious they don't use the same motor. that is more like a comparison that the amps use the same heat-sink. (they don't) but the internals are similar.

and like i said before, zenon is a very high quality board. i know the amp does the power it says, but that msrp price is just crazy.

[Team T&E]

of course there are subtle differences in actual components that are used on board for each said company. i don't know what the dd's went for new, as i said, i don't think they are being produced anymore through dd. and as far as comparing subs to amps...

those subs may use the same baskets, but it is obvious they don't use the same motor. that is more like a comparison that the amps use the same heat-sink. (they don't) but the internals are similar.

and like i said before, zenon is a very high quality board. i know the amp does the power it says, but that msrp price is just crazy.

subtle, are you for real. talk to any amp repair company and they will let you know there are big differances especialy when you use parts that have less than 1% tollerance to say 5% . I sent steve at amp medics a cliff amp for repair and it can not be fixed, why the power supply is not available anywhere only from cliff and they will not sell it but ma is the exact thing right to the untrained eye only.

[CandeShop]

subtle, are you for real. talk to any amp repair company and they will let you know there are big differances especialy when you use parts that have less than 1% tollerance to say 5% . I sent steve at amp medics a cliff amp for repair and it can not be fixed, why the power supply is not available anywhere only from cliff and they will not sell it but ma is the exact thing right to the untrained eye only.


steve at amp medics has had one of my amps before and said something similar about american bass...i discontinued his services and went with a real trained professional.. and a division of Db-R. which is the #1 repair center in the U.S. when it comes to high quality amps or warranty repairs. As for the comparison to the DD yes it does look like the same cosmetic design and board were used, but comparing DD prices to DB Drive...thats like comparing the aston martin price to a hyundai (that is over priced) just not the same

[CandeShop]

makes you say man danny is the best than if he use's such low end not so powerfull amps (3) of them and does 180db emagin if he used 3 stetsom 14k. no not really. there are so the cactus,atomic,AA thay are all the same is what your implieing.

show me where he has put up a 180 db drag legal..only thing i have found on danny is a 178.8db legal and 180.1db outlaw. you cant compare a 180 outlaw to a 180 legal sealed. just not the same

[TazDevil]

hey t&e. show them in the lanes.

[Team T&E]

hey t&e. show them in the lanes.

you know I will :eyebrow:

[Team T&E]

steve at amp medics has had one of my amps before and said something similar about american bass...i discontinued his services and went with a real trained professional.. and a division of Db-R. which is the #1 repair center in the U.S. when it comes to high quality amps or warranty repairs. As for the comparison to the DD yes it does look like the same cosmetic design and board were used, but comparing DD prices to DB Drive...thats like comparing the aston martin price to a hyundai (that is over priced) just not the same

WOW, ADDICTIVE AUDIO must be crappy than, not. steve is the certifeid repair guy for all there amps I'm surre addictive audio would not have chosen him if was not a pro. calling db drive (hyundai) is pretty bad so l would like to see if my hyundai witch is the 2nd loudest certified middel weight ever can hit 160 :oh:

[CandeShop]

WOW, ADDICTIVE AUDIO must be crappy than, not. steve is the certifeid repair guy for all there amps I'm surre addictive audio would not have chosen him if was not a pro. calling db drive (hyundai) is pretty bad so l would like to see if my hyundai witch is the 2nd loudest certified middel weight ever can hit 160 :oh:

i like how you only focused on certain points of that arguement and twisted what was said.. usually that is the workings of someone who already knows that the discussion has been lost due to inproper facts or lack of knowledge:crazy2:

[Team T&E]

show me where he has put up a 180 db drag legal..only thing i have found on danny is a 178.8db legal and 180.1db outlaw. you cant compare a 180 outlaw to a 180 legal sealed. just not the same

danny hays 2009 DB Drag Extream 3-4 world champ 179.7, out law 181.6 at unifiied world finnals 2009. how about that. :rolleyes2:

[Team T&E]

i like how you only focused on certain points of that arguement and twisted what was said.. usually that is the workings of someone who already knows that the discussion has been lost due to inproper facts or lack of knowledge:crazy2:

nop pointing out all your mistakes thats all.

[CandeShop]

danny hays 2009 DB Drag Extream 3-4 world champ 179.7, out law 181.6 at unifiied world finnals 2009. how about that. :rolleyes2:

so maybe your beloved sponsor site should be updated because those numbers i found on db drive's own website where they present themselves as "just breaking world records" but yet dont post up new world record set at world finals last year.


might wanna check your world champs number again http://www.termpro.com/asp/officialevent.asp?EventID=11001&Method=11

178 extreme 3-4 just 2db shy of 180. sorry but you got misinformed. :rolleyes2: look i can roll my eyes...but i use facts

[Team T&E]

World Finals Results
There are no translations available.


dBDRA Official Event: World Championship


World Championship dB Drag Racing Results



dB Drag Racing - Street A
Place Competitor SPL Stats
1st Team Powermusic - Psichas 159.4 •Stats Page

2nd Faber Team Shocker 158.1 •Stats Page

3rd Team Thee Michael Hughes 156.1 •Stats Page


dB Drag Racing - Street B
Place Competitor SPL Stats
1st Team Carmania 161 •Stats Page

2nd Marcos Lepos Ferrari 160.4 •Stats Page

3rd Team Sd 159.3 •Stats Page


dB Drag Racing - Street C
Place Competitor SPL Stats
1st Team DD - Chucky 160.7 •Stats Page

2nd Team Custom - Dale 157.2 •Stats Page

3rd Junior Competition 156.1 •Stats Page


dB Drag Racing - Street Max
Place Competitor SPL Stats
1st Cactus Sounds 165.8 •Stats Page

2nd Flavio Team Shocker 159.1 •Stats Page

3rd Team Innovative Shaun 158.6 •Stats Page


dB Drag Racing - Street Stock
Place Competitor SPL Stats
1st Claudius Vinicius 149.6 •Stats Page

2nd Team All-Tech - Jessica 143.4 •Stats Page

3rd Radek Kesner 141 •Stats Page


dB Drag Racing - Super Street 1-2
Place Competitor SPL Stats
1st dB Devils - M&J 169.7 •Stats Page

2nd Beau Boren 160.8 •Stats Page

3rd Cesar Augusto Dosso 159.2 •Stats Page


dB Drag Racing - Super Street 3-4
Place Competitor SPL Stats
1st Team Gz Lpd - Jens Hoefer 168.3 •Stats Page

2nd Broken Silence - Biggie 108.3 •Stats Page


dB Drag Racing - Super Street 5+
Place Competitor SPL Stats
1st Street Sound Done Massimo 166.1 •Stats Page

2nd The Radio Doctor - Corey 164.6 •Stats Page


dB Drag Racing - Super Street Nw
Place Competitor SPL Stats
1st Dudu Team Shocker 165.6 •Stats Page

2nd Team Carmania - Tom 164.8 •Stats Page

3rd Team XS SPL - No Wall 161.2 •Stats Page

dB Drag Racing - Extreme 1
Place Competitor SPL Stats
1st Team Loud 180.2 •Stats Page


dB Drag Racing - Extreme 2
Place Competitor SPL Stats
1st Team Riprock 180.8 •Stats Page

2nd Team Sgk 178.9 •Stats Page

3rd Gesner Jinichi Arakaki 171.3 •Stats Page


dB Drag Racing - Extreme 3-4
Place Competitor SPL Stats
1st Team Danny Hays 179.7 •Stats Page

2nd Audio - System.de 175.9 •Stats Page


dB Drag Racing - Extreme 5+
Place Competitor SPL Stats
1st Hal Team Shocker 181.6 •Stats Page

2nd Craig Butler 181.1 •Stats Page

3rd Team Kleinlaut 160.3 •Stats Page









Weather
StatsVisits today: 11
Visits yesterday: 37
Visits in this month: 186
Visits in previous month: 644
Visits in this year: 2272
Visits in previous year: 5130
Visits total: 7402
Max.daily visits: 219
Day of max visits: 2009-10-03
Max.monthly visits: 1833
Month of max visits: 2009-10
Impressions today: 85
Impressions yesterday: 160
Impressions this month: 1046
Impressions total: 201423
Bots today: 30
Date since: 2009-09-11

[Team T&E]

your really not getting the point are you.

[CandeShop]

i am getting the point you are in love with db drive...and use any possible chance to try and sway people to use a product that you yourself use. still waiting to see this amp clamped to prove its $4000 price tag

[CandeShop]

dB Drag Racing - Extreme 3-4
Place Competitor SPL Stats
1st Team Danny Hays 179.7 •Stats Page

2nd Audio - System.de 175.9 •Stats Page

well congrats to him...but ouch to go from 179.7 to 178.1 that has to hurt...

[Team T&E]

i am getting the point you are in love with db drive...and use any possible chance to try and sway people to use a product that you yourself use. still waiting to see this amp clamped to prove its $4000 price tag

do i think it's a bad a@# amp yes, not trying to sway anybody you are the one trying to disprove what I have said and so far you haven't done that great of a job, BTW the pic of that db amp is of the first model it was called PT7.5KH

like I said before as soon as I get the new parts for the subs, I will clamp them and see how much power but you have to remember cleaner power gets louder not just shere power you want to use the os scop on the output as well as the input to get the true cleanest power out put. not just balls to the wall how much power can and amp make will determin weather this amp will help your db score in my project one was louder than (4) 6500's. you can do and decide what ever you want. my knowlage and track record speaks for it's self you can hate me or love me but I allway's make nasty systems do they allway's beat everybody no, but I allways place in the top 3 in the world.99% of the time atleast.

[Team T&E]

well congrats to him...but ouch to go from 179.7 to 178.1 that has to hurt...

yup it happens all you can do is fix the problem and go for it again.

[CandeShop]

i would love to see stetsom going down to .34 ohms lawl

this is a little choppy as Alan Dante's english isnt that great

"ok i test 2 amplifiers bridge at 0,7ohms i have 9600 w rms at 12.8 volts, the other test we did was 1 amplifier at 0,7ohms i have see 5000 w rms at 11.6 volts.
ok i just need you all to know ,with 0,7 ohms coil rise to 2.1 ohms.
if you bridge 2 amplifiers at 0,7 ohms eat amplifier see 1.4 ohms, the stetsom amplifiers work diferente in bridge ,ok from 2.1 ohms rise eat amplifier work at 4.2 ohms .
i think the best way to run the stetsom amplifiers, is bridge at 0,25 ohms.
at my test from 0,25 ohms rise to 0,9ohms ,and eat amplifier see 1.8 ohms.
with 1 DD battery(12.8) and 1 amplifier we test at 0,7 ohms ,rise to 2.1 ohms we drop the voltage to 11,2 volts and have 5000 w rms."

so bridged 2 stetsom 7kd at .7 ohms (.35 per amp) with impedence rise to 2.1 ohms they produced 9600 watts at 12.8v just thought i'd show you nominal impedences arent everything its all dependent on your impedence rise

[Team T&E]

this is a little choppy as Alan Dante's english isnt that great

"ok i test 2 amplifiers bridge at 0,7ohms i have 9600 w rms at 12.8 volts, the other test we did was 1 amplifier at 0,7ohms i have see 5000 w rms at 11.6 volts.
ok i just need you all to know ,with 0,7 ohms coil rise to 2.1 ohms.
if you bridge 2 amplifiers at 0,7 ohms eat amplifier see 1.4 ohms, the stetsom amplifiers work diferente in bridge ,ok from 2.1 ohms rise eat amplifier work at 4.2 ohms .
i think the best way to run the stetsom amplifiers, is bridge at 0,25 ohms.
at my test from 0,25 ohms rise to 0,9ohms ,and eat amplifier see 1.8 ohms.
with 1 DD battery(12.8) and 1 amplifier we test at 0,7 ohms ,rise to 2.1 ohms we drop the voltage to 11,2 volts and have 5000 w rms."

so bridged 2 stetsom 7kd at .7 ohms (.35 per amp) with impedence rise to 2.1 ohms they produced 9600 watts at 12.8v just thought i'd show you nominal impedences arent everything its all dependent on your impedence rise

CORRECT, also the encloser will affect the impedence. from experiance in order for this to work you have to roll the volume. okur 7500.1 was tested not at (.35 per amp) but at (.35 st*****) big differance.

[CandeShop]

6500 watts @ 14.4 volts @ 1ohm
17.9 Volts @ .7 st***** = ?

so this is .35 strapped or .7 strapped (.35 per amp)? seems like the story is changing. I know Craig Butler was strapping his 7kd's when he was running Stetsom

"Craig Butler van we run 2 amps bridge at 0.175 ohms with 16 volts" - Alan Dante

[Jeff Stetsom]

i would love to see stetsom going down to .34 ohms lawl

Wattz !!!

well Stetsom will do the job fine at .34ohms nominal impedance !!! if the impedance rise is higher than 1ohm !!! it should be fine as long you have batteries for it !! you know the right electrical system !!!

[Jeff Stetsom]

nice pics but you still have not showed me us a pic of the 7500.1 and no the first pic is not it.

makes you say man danny is the best than if he use's such low end not so powerfull amps (3) of them and does 180db emagin if he used 3 stetsom 14k. no not really. there are so the cactus,atomic,AA thay are all the same is what your implieing.


You know the 3 - 14k give me a call maybe i can do something for you to get them !!! :wink:

561 929 9546

[Team T&E]

so this is .35 strapped or .7 strapped (.35 per amp)? seems like the story is changing. I know Craig Butler was strapping his 7kd's when he was running Stetsom

"Craig Butler van we run 2 amps bridge at 0.175 ohms with 16 volts" - Alan Dante

(did I mention you could strap them at .35 ohms
no thats not in the hand book :))
__________________

nothing has changed from me,mybe just your way of thinking has changed.:banghead3:

[CandeShop]

(did I mention you could strap them at .35 ohms
no thats not in the hand book :))
__________________

nothing has changed from me,mybe just your way of thinking has changed.:banghead3:


6500 watts @ 14.4 volts @ 1ohm
17.9 Volts @ .7 st***** = ?


so maybe you should stick to one story instead of thinking that someone else is being the ignorant one. strap at .35 ohms means .175 per amp..strap at .7 means .35 per amp..just common talk:oh: so :banghead3: on that one

[Team T&E]

so maybe you should stick to one story instead of thinking that someone else is being the ignorant one. strap at .35 ohms means .175 per amp..strap at .7 means .35 per amp..just common talk:oh: so :banghead3: on that one

no, i didn't change anything I was refering to my setup 2 okurs st***** at .7 what will the out put be ?. the fact that they were tested at .35 strapped I never changed or implied anydifferent. I hope this clears up everything for you.:pointnlaugh:

[CandeShop]

yea it cleared up that you heard of a test done...and you have them strapped at .7 nothing hard...many of zenon's cookie cutter amps can be strapped at .7 ohms with proper electrical its just most people dont have the nerve or the need to

[Team T&E]

:beat::beat:yea it cleared up that you heard of a test done...and you have them strapped at .7 nothing hard...many of zenon's cookie cutter amps can be strapped at .7 ohms with proper electrical its just most people dont have the nerve or the need to

:beat:

[TazDevil]

all im hearing is test test test. all i want to be hearing is video video video.

<3

[Team T&E]

yea it cleared up that you heard of a test done...and you have them strapped at .7 nothing hard...many of zenon's cookie cutter amps can be strapped at .7 ohms with proper electrical its just most people dont have the nerve or the need to

up me to, so since you know so much and know so many people can you help us out and show us some video's as taz said so we can all see for our selfs, I can't do anything right now I just opened up another store 3,200 sq feet so I'm to busy to do any video's just just say I'm lying and show us that your not OK.:wink: